2023 Ford F-450 Super Cab DRW 4x4, Godwin 184U Dump Truck (Stock #236072)
Chassis Details
Vehicle Options
- GVWR: 16,500 lb Payload Package
- High Capacity Trailer Tow Package
- Low Deflection Package
- Snow Plow Prep Package
- XL Chrome Package
- Air Conditioning
- Rear Window Defroster
- 120V/400W Outlet
- Power steering
- Power windows
- Remote keyless entry
- Remote Start
- Steering wheel mounted audio controls
- Traction control
- 4-Wheel Disc Brakes
- ABS brakes
- Chrome Front Bumper
- Dual front impact airbags
- Dual front side impact airbags
- Emergency communication system: SYNC 4 911 Assist
- Front anti-roll bar
- Overhead airbag
- Passenger cancellable airbag
- Rear anti-roll bar
- Brake assist
- Delay-off headlights
- Fully automatic headlights
- Halogen Fog Lamps
- Panic alarm
- Speed control
- Dual rear wheels
- Engine Block Heater
- 6-Ton Hydraulic Jack
- Bright Grille
- Heated door mirrors
- Platform Running Boards
- Power door mirrors
- Turn signal indicator mirrors
- Compass
- Exterior Backup Alarm (Pre-Installed)
- Ford Pro Upfit Integration System Removal
- Front reading lights
- Illuminated entry
- Outside temperature display
- Overhead console
- Passenger vanity mirror
- Rear View Camera & Prep Kit
- Tachometer
- Telescoping steering wheel
- Tilt steering wheel
- Trip computer
- Split folding rear seat
- Variably intermittent wipers
- 4.88 Axle Ratio
- Limited Slip w/4.30 Axle Ratio
- View All
Body Details
184U Features
This body is available in lengths of 8' to 11' in 1' increments. Inside width from side to side is 84".
- Features:
- SIDES: One piece sides with no welded seams. 10 gauge A607 grade-50 high tensile steel with boxed top rail and fully welded boxed rear corner post. 6" side board gussets with full length rub rails, and box-type sidebraces.
- RUB RAILS: Full length 45 degree deflector panels are an integral part of the sides.
- FLOOR: 10 gauge two-piece high tensile steel floor with 2" floor to side radius. A607 grade-50 steel.
- FRONT WALL: 10 gauge high tensile A607 grade 50 steel. Full width integral inverted V-type horizontal bracing.
- TAILGATE: 3 Panel fully boxed 10 gauge high tensile A607 grade 50 steel with boxed horizontal reinforcements and sloping lower deflector. Tailgate is 6" higher than side.
- TAILGATE HARDWARE: Heavy duty: Standard upper hardware is offset cast steel hinge. Lower hook is cast steel: engages tailgate pin from top. Banjo eye keeps tailgate chain in position you select.
- LIGHTS & REFLECTORS: FMVSS 108 lights are standard, recessed for protection, rubber mounted and shock proof.
- UNDERSTRUCTURE: Completely jig built with 3" structural channel crossmembers on 12" centers and 5" structural channel longitudinal. Crossmembers are gusseted and welded to longitudinals.
- POPULAR OPTIONS: 36" cab shield, 8 gauge sides, 3/16" one piece floor, fold down 13" sides, 18" sides, quick release upper hardware, other options available.
MPG estimates on this website are EPA estimates; your actual mileage may vary. For used vehicles, MPG estimates are EPA estimates for the vehicle when it was new. The EPA periodically modifies its MPG calculation methodology; all MPG estimates are based on the methodology in effect when the vehicles were new (please see the Fuel Economy portion of the EPAs website for details, including a MPG recalculation tool).
Recently Viewed
You haven’t viewed any vehicles yet.